EN CN

── Products

MODEL 1400 SCR CONTROLS

1400 is Ross Hill Controls' most popular model SCR drive system. Several thousand model 1400 SCR bridges are powering drilling equipment around the world. These bridges are on large and small land rigs and numerous drilling platforms.

029-87300019

product description

ular model SCR drive system. Several thousand model 1400 SCR bridges are powering drilling equipment around the world. These bridges are on large and small land rigs and numerous drilling platforms.

SCR systems usually consist of three, four or five of these bridges depending on the size of the rig. These units can be installed in an SCR Power Control House for the portability required by land drilling operations. Some offshore platforms use an SCR Power Control House or install the SCR line up in the rig package.

The model 1400 SCR cubicle is designed as a front access system minimizing the amount of valuable space the SCR system requires. This system design, like all Ross Hill SCR systems, focuses on simplistic operation, reliability, superior performance and ease of maintenance.

The system is equipped with the following:

     1600AF stationary mount molded case switchwith UV trip and auxiliary contacts

     Ammeter 0-2000ADC

     Voltmeter 0-1000VDC

     SCRON” indicating lamp

     6-pulse, 1800ADC, 750VDC vertical air cooled bridges. Each bridge is protected with two 600A SCR fuses per SCR. On each pair of fuses there is a micro switch that is opened to indicate the fuses have opened. This switch also takes the SCR bridge off line.


INPUT SWITCH/ CIRCUIT 

BREAKER


INPUT VOLTAGE


CONTINUOUS OUTPUT

CURRENT

DRAWWORKS

TYPICAL MAXIMUM SCR LOAD

1600A

600VAC

1800ADC

2000ADC

1600HP- 1700HP

2000A

600VAC

2200ADC

2400ADC

2000ADC

DIMENSIONS

WEIGHT

CLEARANCES

CABLE ENTRY

STANDARD PAINT

40”W x 36"D x 90 H

2500 Lbs.

22.0 Inches

TOP/BOTTOM

ANSI #61 LT. GRAY

The model 1400 SCR 1800A bridge cubicles power:

      Mud Pumps - (Single or dual motor)

      Rotary table or Power Swivel

      Drawworks • (Requires two bridges to power a 2000HP drawworks, or three bridges to power a 3000HP drawworks)

The SCR bridge can be configured for shunt or series motors:

      Series motors require sprocket slip

      Shunt motors require field supplies (Active field supplies required when two motors are powered by a bridge)

      Mud Pump synchronizer available (See sales information sheet)

      PLC based Drillers console available (See sales information sheet)

The SCR bridge is controlled by the DC Control Module. The module is compact and virtually trouble free. The need for servicing and troubleshooting the module have been eliminated because the module can be quickly replaced. All modules of a kind are interchangeable. Each module has a safety feature called zero throttle interlock which will not allow any motor to be powered if assigned with the hand throttle advanced. For specific control module details refer to the information sheet on DC modules.

Dynamic Braking

This is a motor brake, designed to slow the drawworks motors and cathead to a preset cathead speed within 10-15 seconds after driller releases the foot throttle. The dynamic brake circuit connects the drawworks motors to a steel grid resistor bank. The energy in the free wheeling DC motors is dissipated in the grid resistor bank. After the braking cycle is completed, the resistor bank is disconnected from the motor and does not interfere with normal drawworks operation.

Bridge Control

Bridges are controlled from the driller's console. The console is located on the drill floor near the drawworks. The console is watertight; constructed with the highest quality stainless steel and is equipped with an air purging valve. Refer to the equipment information sheet on Ross Hill Consoles for additional information.

      Protective functions built into the bridge circuit

      SCR bridge over temperature

      ency off (Activated by switch on the driller's console)

      Shutdown for SCR fuse failure

Ross Hill Controls has a very strong customer support team comprised of engineering, field service, and parts and training which makes us the first choice in the drilling industry. You are not alone with Ross Hill Controls.

Our experienced service specialists are available 24 Hours a day to assist your technical personnel in solving problems and to minimize system down time. You can count on us to make the entire SCR system work.